How to make pumpkin decor that looks like the ones you’d find in a Halloween party
Posted On August 6, 2021
How to decorate your house like the Pumpkin Festival of Lights!
You can buy pumpkin decor online from all of the great shops in this article.
If you don’t know where to start, here are some tips to get you started.
Make sure the pumpkin is in the proper position on the wall.
It needs to be in the correct position.
The best way to do this is to cut off the bottom half of the pumpkin.
You want the pumpkin to hang up in the air, which is what you’ll be decorating with.
Cut off a piece of paper about an inch wide and about a half inch high, and trim the excess off.
Make it into a small, flat square.
When you’re done trimming the paper, place the square in the center of the wall, about 1/4-inch away from the top and bottom of the circle.
You’ll want the paper in this position to make sure that when you put the pumpkin down, the top of the square will be facing up and down.
You can also place it in this place if you have other decorating supplies around.
Cut the corner.
This is where you’ll need to cut the paper that you made.
Start by cutting out a small circle about 1 inch by 1 inch wide, with the center about 1 1/2 inches from the edges.
You will want to cut this circle in half, and place it at the bottom of each side of the box.
The edges of the paper will also need to be cut to make this happen.
Trim the top two-thirds of the corner paper.
Once you’ve cut out your circle, you’ll want to trim the top three-quarters of the cardboard, leaving about 1 3/4 inches between each section of cardboard.
You don’t want to do too much trimming, because you want the cardboard to be easy to cut.
This will help to create a more even appearance of the decorations.
Cut out the bottom portion of the triangle.
The bottom half should be about 1-inch wide and 3-4 inches tall.
You may want to go a little smaller than this to make the corners easier to cut and to allow for a more level surface.
You should also consider making the edges a little larger so that they’re easier to trim.
Cut a small section of paper at the top.
Cut two pieces of cardboard, one at each corner of the center section.
You could cut these pieces into little triangles, but I found that I like to cut them a little shorter, about a quarter inch, and that way, I can trim them without the cardboard falling out.
Cut another piece of cardboard at the center.
Now, cut another section of 1-1/2-inch cardboard.
Cut it to about a third of an inch tall, so that it will fit neatly into the middle of the corners.
Now cut a little piece of another piece at the end of the middle section.
Cut three sections of 1/8-inch paper, and a quarter of an eighth of an extra inch of paper to fit between the sections of cardboard that you cut at the beginning of the section.
Now trim the cardboard into the corner of each section, leaving a little room for the paper to come out.
You do not want to be too loose, because trimming can be very messy.
Cut an additional section of one-quarter of an additional inch of cardboard so that you can put it on top of each corner.
Cut six more pieces of paper.
Trimming the corners can be a bit tricky, because the cardboard is so thin, so the paper needs to stretch a little.
If the paper doesn’t stretch enough, it can be difficult to trim them, but you can trim it easily enough to get the best result.
Cut your decorations.
The next step is to trim all the paper off of the sides of the boxes, and to place them on the sides.
Once the paper is off, trim off the top, and the bottom.
Cut four squares, each about 2 inches long, and three sections shorter than the first.
Place them on top and the two bottom squares.
Trims should look like the picture at the right, with only the bottom square touching the cardboard.
Cut about one-fourth of a inch off the middle and bottom sections.
Trimb the sides to create the base for your decorations!
Once you have the paper cut, you can cut out the cardboard pieces to the right size.
You probably want to place the cardboard on a large flat surface, like a table, to create an easier and less messy cut.
You might also want to leave some of the space for the sides in the middle.
If that’s the case, trim the paper so that the cardboard will fit snugly.
The cardboard is very sticky, so you can use some toothpicks to remove the